[lvc-project] [PATCH v2] wifi: ar5523: enable proper endpoint verification
Stefan Lippers-Hollmann
s.l-h at gmx.de
Sun Apr 28 10:04:04 MSK 2024
Hi
On 2024-04-25, Kalle Valo wrote:
> Kalle Valo <kvalo at kernel.org> writes:
> > Nikita Zhandarovich <n.zhandarovich at fintech.ru> wrote:
[...]
> > Does anyone have a real device to test this? I have had so much problems with
> > syzbot fixes in the past that I'm hesitant to take such patches without
> > testing.
>
> Actually should we just remove ar5523 driver? Has anyone heard anyone
> using this driver still?
While I'm not using it regularly, the driver does still work in plain
v6.8.8 (and these Netgear WG111 and WG111T USB WLAN cards were quite
common), tested against a qcn5024 AP.
I'm just preparing a new kernel build with the proposed patch applied.
$ uname -r
6.8.8
[ 54.027188] usb 3-5: new high-speed USB device number 5 using xhci_hcd
[ 54.154514] usb 3-5: New USB device found, idVendor=1385, idProduct=4251, bcdDevice= 0.01
[ 54.154531] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 54.154537] usb 3-5: Product: WG111T
[ 54.154541] usb 3-5: Manufacturer: Atheros Communications Inc
[ 54.154545] usb 3-5: SerialNumber: 1.0
[ 54.262777] usbcore: registered new interface driver ar5523
[ 54.411417] usb 3-5: USB disconnect, device number 5
[ 54.660141] usb 3-5: new high-speed USB device number 6 using xhci_hcd
[ 54.787463] usb 3-5: New USB device found, idVendor=1385, idProduct=4250, bcdDevice= 0.01
[ 54.787478] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 54.787483] usb 3-5: Product: WG111T
[ 54.787487] usb 3-5: Manufacturer: Atheros Communications Inc
[ 54.787491] usb 3-5: SerialNumber: 1.0
[ 54.835897] usb 3-5: Cap: CAP_TARGET_VERSION=0x00000006
[ 54.836738] usb 3-5: Cap: CAP_TARGET_REVISION=0x00000001
[ 54.836985] usb 3-5: Cap: CAP_MAC_VERSION=0x00000008
[ 54.837269] usb 3-5: Cap: CAP_MAC_REVISION=0x00000001
[ 54.837578] usb 3-5: Cap: CAP_PHY_REVISION=0x00000046
[ 54.837828] usb 3-5: Cap: CAP_ANALOG_5GHz_REVISION=0x00000046
[ 54.838114] usb 3-5: Cap: CAP_ANALOG_2GHz_REVISION=0x00000000
[ 54.838364] usb 3-5: Cap: CAP_REG_DOMAIN=0x00000000
[ 54.838635] usb 3-5: Cap: CAP_REG_CAP_BITS=0x00000000
[ 54.838876] usb 3-5: Cap: CAP_WIRELESS_MODES=0x00000000
[ 54.839138] usb 3-5: Cap: CAP_CHAN_SPREAD_SUPPORT=0x0000001c
[ 54.839446] usb 3-5: Cap: CAP_COMPRESS_SUPPORT=0x00000001
[ 54.839685] usb 3-5: Cap: CAP_BURST_SUPPORT=0x00000001
[ 54.839954] usb 3-5: Cap: CAP_FAST_FRAMES_SUPPORT=0x00000001
[ 54.840216] usb 3-5: Cap: CAP_CHAP_TUNING_SUPPORT=0x00000001
[ 54.840467] usb 3-5: Cap: CAP_TURBOG_SUPPORT=0x00000001
[ 54.840724] usb 3-5: Cap: CAP_TURBO_PRIME_SUPPORT=0x00000001
[ 54.840975] usb 3-5: Cap: CAP_DEVICE_TYPE=0x00000001
[ 54.841236] usb 3-5: Cap: CAP_WME_SUPPORT=0x00000001
[ 54.841506] usb 3-5: Cap: CAP_TOTAL_QUEUES=0x00000001
[ 54.841744] usb 3-5: Cap: CAP_CONNECTION_ID_MAX=0x0000000a
[ 54.842039] usb 3-5: Cap: CAP_LOW_5GHZ_CHAN=0x00000004
[ 54.842281] usb 3-5: Cap: CAP_HIGH_5GHZ_CHAN=0x00001338
[ 54.842554] usb 3-5: Cap: CAP_LOW_2GHZ_CHAN=0x000017d4
[ 54.842788] usb 3-5: Cap: CAP_HIGH_2GHZ_CHAN=0x00000908
[ 54.843056] usb 3-5: Cap: CAP_TWICE_ANTENNAGAIN_5G=0x00000001
[ 54.843343] usb 3-5: Cap: CAP_TWICE_ANTENNAGAIN_2G=0x00000004
[ 54.843593] usb 3-5: Cap: CAP_CIPHER_AES_CCM=0x00000001
[ 54.843851] usb 3-5: Cap: CAP_CIPHER_TKIP=0x00000000
[ 54.844113] usb 3-5: Cap: CAP_MIC_TKIP=0x00000000
[ 54.844677] usb 3-5: MAC/BBP AR5523, RF AR2112
[ 54.845129] usb 3-5: Found and initialized AR5523 device
[ 54.853451] ar5523 3-5:1.0 wlx<MAC>: renamed from wlan0
[ 79.311092] wlx<MAC>: 80 MHz not supported, disabling VHT
[ 79.314464] wlx<MAC>: authenticate with 9X:XX:XX:XX:XX:01 (local address=0X:XX:XX:XX:XX:65)
[ 79.314472] wlx<MAC>: send auth to 9X:XX:XX:XX:XX:01 (try 1/3)
[ 79.365058] wlx<MAC>: authenticate with 9X:XX:XX:XX:XX:01 (local address=0X:XX:XX:XX:XX:65)
[ 79.365073] wlx<MAC>: send auth to 9X:XX:XX:XX:XX:01 (try 1/3)
[ 79.368361] wlx<MAC>: authenticated
[ 79.369488] wlx<MAC>: associate with 9X:XX:XX:XX:XX:01 (try 1/3)
[ 79.376783] wlx<MAC>: RX AssocResp from 9X:XX:XX:XX:XX:01 (capab=0x1431 status=0 aid=1)
[ 79.377789] wlx<MAC>: associated
[ 79.412980] wlx<MAC>: deauthenticating from 9X:XX:XX:XX:XX:01 by local choice (Reason: 1=UNSPECIFIED)
[ 79.613018] wlx<MAC>: 80 MHz not supported, disabling VHT
[ 79.618057] wlx<MAC>: authenticate with 9X:XX:XX:XX:XX:53 (local address=0X:XX:XX:XX:XX:65)
[ 79.618068] wlx<MAC>: send auth to 9X:XX:XX:XX:XX:53 (try 1/3)
[ 79.672878] wlx<MAC>: authenticate with 9X:XX:XX:XX:XX:53 (local address=0X:XX:XX:XX:XX:65)
[ 79.672885] wlx<MAC>: send auth to 9X:XX:XX:XX:XX:53 (try 1/3)
[ 79.675745] wlx<MAC>: authenticated
[ 79.676415] wlx<MAC>: associate with 9X:XX:XX:XX:XX:53 (try 1/3)
[ 79.682446] wlx<MAC>: RX AssocResp from 9X:XX:XX:XX:XX:53 (capab=0x1031 status=0 aid=1)
[ 79.683079] wlx<MAC>: associated
[ 79.708364] wlx<MAC>: deauthenticating from 9X:XX:XX:XX:XX:53 by local choice (Reason: 1=UNSPECIFIED)
[ 79.913528] wlx<MAC>: 80 MHz not supported, disabling VHT
[ 79.916480] wlx<MAC>: authenticate with 9X:XX:XX:XX:XX:b1 (local address=0X:XX:XX:XX:XX:65)
[ 79.916489] wlx<MAC>: send auth to 9X:XX:XX:XX:XX:b1 (try 1/3)
[ 79.979005] wlx<MAC>: authenticate with 9X:XX:XX:XX:XX:b1 (local address=0X:XX:XX:XX:XX:65)
[ 79.979019] wlx<MAC>: send auth to 9X:XX:XX:XX:XX:b1 (try 1/3)
[ 79.982175] wlx<MAC>: authenticated
[ 79.983460] wlx<MAC>: associate with 9X:XX:XX:XX:XX:b1 (try 1/3)
[ 79.990499] wlx<MAC>: RX AssocResp from 9X:XX:XX:XX:XX:b1 (capab=0x1431 status=0 aid=1)
[ 79.991150] wlx<MAC>: associated
[ 80.004037] wlx<MAC>: Limiting TX power to 20 (20 - 0) dBm as advertised by 9X:XX:XX:XX:XX:b1
[ 80.017058] wlx<MAC>: deauthenticating from 9X:XX:XX:XX:XX:b1 by local choice (Reason: 1=UNSPECIFIED)
[ 81.031824] wlx<MAC>: 80 MHz not supported, disabling VHT
[ 81.036498] wlx<MAC>: authenticate with 9X:XX:XX:XX:XX:b1 (local address=0X:XX:XX:XX:XX:65)
[ 81.036506] wlx<MAC>: send auth to 9X:XX:XX:XX:XX:b1 (try 1/3)
[ 81.039194] wlx<MAC>: authenticated
[ 81.040489] wlx<MAC>: associate with 9X:XX:XX:XX:XX:b1 (try 1/3)
[ 81.047244] wlx<MAC>: RX AssocResp from 9X:XX:XX:XX:XX:b1 (capab=0x1431 status=0 aid=1)
[ 81.047905] wlx<MAC>: associated
[ 81.088917] wlx<MAC>: deauthenticating from 9X:XX:XX:XX:XX:b1 by local choice (Reason: 1=UNSPECIFIED)
[ 82.086878] wlx<MAC>: 80 MHz not supported, disabling VHT
[ 82.091343] wlx<MAC>: authenticate with aX:XX:XX:XX:XX:01 (local address=0X:XX:XX:XX:XX:65)
[ 82.091351] wlx<MAC>: send auth to aX:XX:XX:XX:XX:01 (try 1/3)
[ 82.101245] wlx<MAC>: authenticated
[ 82.102400] wlx<MAC>: associate with aX:XX:XX:XX:XX:01 (try 1/3)
[ 82.107565] wlx<MAC>: RX AssocResp from aX:XX:XX:XX:XX:01 (capab=0x1431 status=0 aid=2)
[ 82.108175] wlx<MAC>: associated
[ 82.196524] wlx<MAC>: Limiting TX power to 20 (20 - 0) dBm as advertised by aX:XX:XX:XX:XX:01
# wpa_cli -i wlx<MAC> status
bssid=aX:XX:XX:XX:XX:01
freq=2437
ssid=XXX
id=2
id_str=XXX
mode=station
pairwise_cipher=CCMP
group_cipher=CCMP
key_mgmt=WPA2-PSK
wpa_state=COMPLETED
address=0X:XX:XX:XX:XX:65
uuid=XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX
$ iperf3 -c <remote_server_ipv6>
Connecting to host <remote_server_ipv6>, port 5201
[ 5] local 2aXX:XXX:XXXX:XXXX:XXXX:XXXX:XXX:XX65 port 47110 connected to 2aXX:XXX:XXXX:XXXX:XXXX:XXXX:XXX:XX01 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 384 KBytes 3.14 Mbits/sec 14 13.9 KBytes
[ 5] 1.00-2.00 sec 256 KBytes 2.10 Mbits/sec 8 13.9 KBytes
[ 5] 2.00-3.00 sec 0.00 Bytes 0.00 bits/sec 0 1.39 KBytes
[ 5] 3.00-4.00 sec 0.00 Bytes 0.00 bits/sec 1 18.1 KBytes
[ 5] 4.00-5.00 sec 0.00 Bytes 0.00 bits/sec 0 18.1 KBytes
[ 5] 5.00-6.00 sec 0.00 Bytes 0.00 bits/sec 0 23.7 KBytes
[ 5] 6.00-7.00 sec 128 KBytes 1.05 Mbits/sec 0 23.7 KBytes
[ 5] 7.00-8.00 sec 0.00 Bytes 0.00 bits/sec 0 23.7 KBytes
[ 5] 8.00-9.00 sec 0.00 Bytes 0.00 bits/sec 0 23.7 KBytes
[ 5] 9.00-10.00 sec 0.00 Bytes 0.00 bits/sec 0 23.7 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 768 KBytes 629 Kbits/sec 23 sender
[ 5] 0.00-10.19 sec 512 KBytes 411 Kbits/sec receiver
iperf Done.
$ iperf3 -c <remote_server_ipv6> --reverse
Connecting to host <remote_server_ipv6>, port 5201
Reverse mode, remote host <remote_server_ipv6> is sending
[ 5] local 2aXX:XXX:XXXX:XXXX:XXXX:XXXX:XXX:XX65 port 39628 connected to 2aXX:XXX:XXXX:XXXX:XXXX:XXXX:XXX:XX01 port 5201
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 768 KBytes 6.28 Mbits/sec
[ 5] 1.00-2.00 sec 1.12 MBytes 9.44 Mbits/sec
[ 5] 2.00-3.00 sec 1.12 MBytes 9.43 Mbits/sec
[ 5] 3.00-4.00 sec 1.12 MBytes 9.45 Mbits/sec
[ 5] 4.00-5.00 sec 896 KBytes 7.34 Mbits/sec
[ 5] 5.00-6.00 sec 1.12 MBytes 9.43 Mbits/sec
[ 5] 6.00-7.00 sec 1.38 MBytes 11.5 Mbits/sec
[ 5] 7.00-8.00 sec 1.12 MBytes 9.44 Mbits/sec
[ 5] 8.00-9.00 sec 1.25 MBytes 10.5 Mbits/sec
[ 5] 9.00-10.00 sec 1.50 MBytes 12.6 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.10 sec 13.6 MBytes 11.3 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 11.4 MBytes 9.54 Mbits/sec receiver
iperf Done.
$ iperf3 -c <remote_server_ipv6> --bidir
Connecting to host <remote_server_ipv6>, port 5201
[ 5] local 2aXX:XXX:XXXX:XXXX:XXXX:XXXX:XXX:XX65 port 38430 connected to 2aXX:XXX:XXXX:XXXX:XXXX:XXXX:XXX:XX01 port 5201
[ 7] local 2aXX:XXX:XXXX:XXXX:XXXX:XXXX:XXX:XX65 port 38446 connected to 2aXX:XXX:XXXX:XXXX:XXXX:XXXX:XXX:XX01 port 5201
[ ID][Role] Interval Transfer Bitrate Retr Cwnd
[ 5][TX-C] 0.00-1.00 sec 128 KBytes 1.05 Mbits/sec 6 4.18 KBytes
[ 7][RX-C] 0.00-1.00 sec 768 KBytes 6.28 Mbits/sec
[ 5][TX-C] 1.00-2.00 sec 0.00 Bytes 0.00 bits/sec 7 1.39 KBytes
[ 7][RX-C] 1.00-2.00 sec 1.00 MBytes 8.39 Mbits/sec
[ 5][TX-C] 2.00-3.00 sec 0.00 Bytes 0.00 bits/sec 3 1.39 KBytes
[ 7][RX-C] 2.00-3.00 sec 896 KBytes 7.35 Mbits/sec
[ 5][TX-C] 3.00-4.00 sec 128 KBytes 1.05 Mbits/sec 2 2.79 KBytes
[ 7][RX-C] 3.00-4.00 sec 896 KBytes 7.34 Mbits/sec
[ 5][TX-C] 4.00-5.00 sec 0.00 Bytes 0.00 bits/sec 3 2.79 KBytes
[ 7][RX-C] 4.00-5.00 sec 1.12 MBytes 9.43 Mbits/sec
[ 5][TX-C] 5.00-6.00 sec 0.00 Bytes 0.00 bits/sec 3 1.39 KBytes
[ 7][RX-C] 5.00-6.00 sec 1.38 MBytes 11.5 Mbits/sec
[ 5][TX-C] 6.00-7.00 sec 0.00 Bytes 0.00 bits/sec 3 2.79 KBytes
[ 7][RX-C] 6.00-7.00 sec 1.25 MBytes 10.5 Mbits/sec
[ 5][TX-C] 7.00-8.00 sec 0.00 Bytes 0.00 bits/sec 3 2.79 KBytes
[ 7][RX-C] 7.00-8.00 sec 1.38 MBytes 11.5 Mbits/sec
[ 5][TX-C] 8.00-9.00 sec 0.00 Bytes 0.00 bits/sec 2 2.79 KBytes
[ 7][RX-C] 8.00-9.00 sec 1.50 MBytes 12.6 Mbits/sec
[ 5][TX-C] 9.00-10.00 sec 0.00 Bytes 0.00 bits/sec 1 4.18 KBytes
[ 7][RX-C] 9.00-10.00 sec 1.50 MBytes 12.6 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-10.00 sec 256 KBytes 210 Kbits/sec 33 sender
[ 5][TX-C] 0.00-10.06 sec 128 KBytes 104 Kbits/sec receiver
[ 7][RX-C] 0.00-10.00 sec 13.8 MBytes 11.5 Mbits/sec 0 sender
[ 7][RX-C] 0.00-10.06 sec 11.6 MBytes 9.70 Mbits/sec receiver
iperf Done.
Regards
Stefan Lippers-Hollmann
More information about the lvc-project
mailing list