[lvc-project] [PATCH] drm/i915/edp: Check supported link rates DPCD read

[Jani Nikula]

On Fri, 29 May 2026, Nikita Zhandarovich <n.zhandarovich at fintech.ru> wrote:
> intel_edp_set_sink_rates() reads DP_SUPPORTED_LINK_RATES into a local
> stack array and then parses the array unconditionally. If the read
> fails or returns less data than requested, the array contents are not
> valid and may result in bogus sink link rates being used.
>
> Check that the full DPCD block was read before parsing it. If not, fall
> back to the default sink rate handling.
>
> Found by Linux Verification Center (linuxtesting.org) with static
> analysis tool SVACE.

Thanks for the patch.

>
> Fixes: 68f357cb7347 ("drm/i915/dp: generate and cache sink rate array for all DP, not just eDP 1.4")
> Signed-off-by: Nikita Zhandarovich <n.zhandarovich at fintech.ru>
> ---
>  drivers/gpu/drm/i915/display/intel_dp.c | 11 +++++++++--
>  1 file changed, 9 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
> index 6ef2a0043cda..b6650a12ca54 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> @@ -4678,10 +4678,16 @@ intel_edp_set_sink_rates(struct intel_dp *intel_dp)
>  
>  	if (intel_dp->edp_dpcd[0] >= DP_EDP_14) {
>  		__le16 sink_rates[DP_MAX_SUPPORTED_RATES];
> +		ssize_t ret;
>  		int i;
>  
> -		drm_dp_dpcd_read(&intel_dp->aux, DP_SUPPORTED_LINK_RATES,
> -				 sink_rates, sizeof(sink_rates));
> +		ret = drm_dp_dpcd_read(&intel_dp->aux, DP_SUPPORTED_LINK_RATES,
> +				       sink_rates, sizeof(sink_rates));

Please switch to drm_dp_dpcd_read_data(). It'll return < 0 for errors,
and is easier to deal with.

> +		if (ret != sizeof(sink_rates)) {
> +			drm_dbg_kms(display->drm,
> +				    "Unable to read eDP supported link rates, using default rates\n");
> +			goto use_default_rates;

I think I'd avoid the goto and use:

	memset(sink_rates, 0, sizeof(sink_rates));

BR,
Jani.

> +		}
>  
>  		for (i = 0; i < ARRAY_SIZE(sink_rates); i++) {
>  			int rate;
> @@ -4715,6 +4721,7 @@ intel_edp_set_sink_rates(struct intel_dp *intel_dp)
>  	 * Use DP_LINK_RATE_SET if DP_SUPPORTED_LINK_RATES are available,
>  	 * default to DP_MAX_LINK_RATE and DP_LINK_BW_SET otherwise.
>  	 */
> +use_default_rates:
>  	if (intel_dp->num_sink_rates)
>  		intel_dp->use_rate_select = true;
>  	else

-- 
Jani Nikula, Intel